TT Club Addresses Crane Safety in Windy Conditions

Thursday, October 16, 2008

Analysis of the TT Club’s claims over a number of years has highlighted that wind damage to quayside cranes is the biggest weather related cost to terminals. Due to their size, profile and location on the quayside, these cranes are particularly susceptible to wind, and care must be taken in the design and operating procedures to protect against the crane being blown over or along the rails.

Such incidents can be prevented, or at least the collateral damage caused can be restricted, by having appropriate procedures and ensuring that they are followed. Essential elements include: having effective national and local weather forecasting systems and ensuring that operational procedures respond appropriately when sufficient warning is forthcoming. In addition, good practice would dictate that storm pin or tie-down facilities and procedures are invoked.

Furthermore, appropriately designed braking systems, which are properly maintained, can significantly help in conditions of sudden wind bursts. There are two major windstorm issues to be considered: protection against forecast strong winds, and protection against sudden local winds called micro-bursts.

In the case of forecast strong winds, storm pins and tie-downs of sufficient number and size to hold a crane structure stationary (and procedures to implement these) are required to protect quayside cranes. Storm pins are vertical sliding pins mounted at suitable positions under each leg of the crane. These pins are dropped into sockets set into the surface of the berth. The pins must be interlocked with the travel motion so that the crane can only be moved when the pins are disengaged.

Storm tie-downs are connections on the crane, normally at the four corners, where suitable slings, chains or bars of appropriate size and number are fitted to connect to anchor points in the terminal pavement. These anchors must be able to hold the loadings of the crane under potential wind conditions.

The other situation of primary danger is the occurrence of microbursts. In the worst circumstances, unknown to the driver, a strong wind arises blowing in the same direction in which the crane is travelling and the driver is unable to stop the motion of the crane. To deal with these situations, suitable storm brakes and service brakes are necessary and should be fitted to the crane. These are not however, an acceptable alternative to pins or tie-downs for forecast weather conditions.

There are a number of different systems used for storm brakes or, as they are sometimes called, parking brakes. These include rail clamps and railhead brakes. However, these are static brakes. They are only applied when the crane has stopped moving. They normally operate if the emergency stop is activated and unless severely damaged will help prevent a stationary crane from being pushed along by the wind. Their main purpose and benefit is to park and anchor the crane between normal operations without the need to apply the storm pins or tie-downs.

If rail clamp and railhead brakes are applied when the crane is moving, both the brakes themselves and the crane rail can be damaged. For this reason, wheel brakes should also be installed. These are normally disc brakes mounted on the crane wheels. Finally, the service braking system forms the normal operating brake. This is part of the motor and gearbox of the crane, which slows and ultimately stops the crane during daily working.

Apart from accurate weather forecasting and adequate technical measures, both maintenance and training are crucial to safer procedures.

The TT Club urges terminal managers concerned with quayside cranes and bulk loaders/unloaders to review their emergency plans in respect of high wind situations and ensure that all necessary measures have been taken to prevent injury, damage and downtime arising from this cause.

(www.ttclub.com)

Maritime Reporter May 2015 Digital Edition
FREE Maritime Reporter Subscription
Latest Maritime News    rss feeds

Maritime Safety

USCG Provides Safety Tips to Paddlesports Enthusiasts

As the boating season unofficially begins, the 9th Coast Guard District is reminding paddlesport enthusiasts to take precautions to ensure safe trips and increase

Wärtsilä's' Propulsion for Use with US Compliant ELA

Wärtsilä has developed propulsion systems that are capable of operating with Environmentally Acceptable Lubricants (EALs) and comply with the US Vessel General Permit 2013 (VGP-2013).

USS George Washington Completes Carrier Qualifications

Carrier Air Wing (CVW) 5 and the Nimitz-class aircraft carrier USS George Washington (CVN 73) completed its carrier qualifications (CQ), May 23. CQ allows

 
 
Maritime Security Naval Architecture Offshore Oil Pipelines Pod Propulsion Salvage Ship Repair Ship Simulators Shipbuilding / Vessel Construction Winch
rss | archive | history | articles | privacy | contributors | top maritime news | about us | copyright | maritime magazines
maritime security news | shipbuilding news | maritime industry | shipping news | maritime reporting | workboats news | ship design | maritime business

Time taken: 0.1618 sec (6 req/sec)