Heinkel Enhance Loctite Retaining Adhesive Products

MaritimeEquipment.com
Sunday, October 13, 2013

Henkel Corporation has enhanced three Loctite® anaerobic retaining compounds to allow primerless performance on oily or contaminated surfaces, even at operating temperatures as high as 180°C.

Used in combination with interference fits to secure bearings, bushings, gears and cylindrical assemblies into housings or shafts, Loctite® 638™, 648™ and 680™ Retaining Compounds allow higher load transmission, better performance with existing designs, relaxed machining tolerances and reductions in the size, weight and overall cost of an assembly.

All three improved Loctite® retaining adhesives make joints stronger distribute stress evenly, prevent corrosion and fretting and reduce or eliminate expensive machining and surface-finishing operations.

Loctite® 638™ is a general-purpose retaining compound recommended for press fits that will need subsequent disassembly. Designed for use on loose-fitting parts,
this globally-available, high-strength adhesive resists temperatures to 175°C and can be used on applications with larger gaps approaching 0.25 mm. The adhesive is registered to NSF Category P1.

Loctite® 648™ is a high-strength retaining compound recommended for continuous working temperatures to 180°C. This globally-available, general-purpose retaining adhesive fixtures in five minutes with full cure in 24 hours and is designed for use on close-fitting parts. The high-strength formulation bonds well to stainless steel press and interference fits, and fills gaps to 0.15 mm. The adhesive is certified to ANSI/NSF Standard 61 for use in potable water systems.

Loctite® 680™ is a high-strength retaining adhesive for use on slip-fitted parts with gaps as large as 0.38 mm. This low-viscosity material is certified to ANSI/NSF Standard 61 for use in potable water systems.

For additional information and to request a sample of Loctite® 648™ and a copy of the new Loctite® Retaining Compound Design Guide, go to www.loctiteretaining.com.

 

Maritime Today


The Maritime Industry's original and most viewed E-News Service

Maritime Reporter April 2016 Digital Edition
FREE Maritime Reporter Subscription
Latest Maritime News    rss feeds

Marine Materials

Ocean Economy Set to Double in Size by 2030

The world’s oceans must be managed well to ensure the potential of an “ocean economy” that was worth US $ 1.5 trillion in 2010.   "Calculations based on the

Aging Seaborne Steel Products

In 2015, seaborne steel products trade accounted for around a fifth of minor bulk trade, having grown on average by 6 percent per annum since 2010, according to Clarksons Research.

Hempel’s Fouling Defence Product Hempaguard Applied to 500 Vessels

Leading marine coatings manufacturer, Hempel, announces - after only two and a half years on the market -  its award winning innovative fouling defence product

Marine Equipment

Mercury Marine Expands Manufacturing Capacity

Mercury Marine is adding a 53,000 square foot manufacturing capacity expansion to its global headquarters in Fond du Lac, Wisc. The expansion will consist of 45,

Conquest Installs 850t Crane on Allseas Solitaire

Conquest Offshore was contracted by Allseas to remove a 300-ton crane and transport and install a 850-ton Huisman crane on board of one of the largest pipe-lay vessels in the world, Allseas Solitaire.

Sellick Equipment to Open New Facility

On April, 20, 2016, at the young age of 97 years, Walter Sellick along with sons Howard Sellick - President, David Sellick - Vice President and grandson Colin Sellick - Systems Manager,

 
 
Maritime Contracts Maritime Security Maritime Standards Navigation Pipelines Pod Propulsion Ship Electronics Ship Repair Ship Simulators Winch
rss | archive | history | articles | privacy | contributors | top maritime news | about us | copyright | maritime magazines
maritime security news | shipbuilding news | maritime industry | shipping news | maritime reporting | workboats news | ship design | maritime business

Time taken: 0.0512 sec (20 req/sec)